Interactive Laboratory Engine

Water Change GH/KH Calculator

Work out how a water change shifts your tank's GH, how much tap and RO/DI water to blend to hit a target GH, or how many grams of remineralizer and baking soda to add to pure RO water. Enter tank or batch volume, current and target hardness, and the product constants from your label.

Laboratory Console Engine // SYS.2.5
ONLINE
Calibration Controls
13 Parameters
Diagnostic Telemetry
Console Standby

Awaiting Parameter Calibration

Adjust parameters in the left console to initiate real-time telemetry and biological safety verification.

Water Chemistry Mixing

Standardized Laboratory Specs
1 dGH17.85 ppm (as CaCO3)
1 meq/Labout 2.8 dGH
Equilibrium (label)16 g per 80 L raises GH by about 3 dGH
Baking soda (calculated)about 3 g per 100 L raises KH by 1 dKH
โœ“
Target Operational Envelope OPTIMAL

Target hardness depends on species; match it to the animals you keep rather than a generic number.

โš ๏ธ
Critical Operating Boundary HAZARD

Rapid GH, KH or pH swings during a single water change.

Standard Volumetric Calibration Presets Standard Footprints
After a water change64 L, GH 10, 10% change with GH 3 water gives GH 9.3
Tap and RO mixTap GH 14, RO GH 0, target 6 gives 43% tap and 57% RO
Remineralize RO20 L RO to GH 6 with Equilibrium needs about 8 g
Failure Mode & Hazard Mitigation Analysis
Dosing minerals into evaporation top-off waterMODERATE

Top off with plain RO/DI and add minerals only to water used for changes.

Large single-step hardness changesHIGH

Change in small steps and match new water to tank values.

Using the wrong product constantMODERATE

Use the figure on your pack's label and test the batch before adding it.

Water changes do more than remove nitrate. When your new water has a different hardness from your tank, every change shifts GH and KH. This calculator shows the result of a water change, works out the tap-to-RO mix needed to reach a target GH, and estimates how much remineralizer or baking soda to add to pure RO or DI water.

Three Calculations in One

  1. Result after a water change: enter tank volume, current GH, the percentage you change and the GH of the new water. You get the GH left in the tank.
  2. Tap + RO mix ratio: enter your tap GH, your RO/DI GH and your target GH. You get the percentage and litres of each to blend.
  3. Remineralize RO/DI: enter the batch volume and target GH. You get the grams of remineralizer to dissolve, and optionally the grams of baking soda for KH.

The Formulas

Mixing two waters is a volume-weighted average: final = (V1 x C1 + V2 x C2) / (V1 + V2). To find how much tap water you need: tap fraction = (target - RO) / (tap - RO). This only works when the target lies between the RO and tap values. For remineralizing, dose per litre = (target GH - starting GH) / (GH gain per gram per litre of your product).

Worked Examples

After a water change: a 64 L tank at GH 10, with a 10% change using GH 3 water. Old water left: 57.6 L x 10 = 576. New water: 6.4 L x 3 = 19.2. Final GH = (576 + 19.2) / 64 = 9.3 dGH.

Mix ratio: tap GH 14, RO GH 0, target GH 6. Tap fraction = 6 / 14 = 43%. For a 20 L batch use about 8.6 L tap and 11.4 L RO.

Remineralize RO: Seachem Equilibrium is labeled at 16 g per 80 L to raise GH by about 3 dGH, that is 0.2 g per litre per 3 dGH. For a 6 dGH target in 20 L of RO water: 6 / 3 x 0.2 g/L x 20 L = 8 g.

GH vs KH

GH measures dissolved calcium and magnesium. KH measures carbonate and bicarbonate buffering. Blending tap with RO lowers both together. Equilibrium-style GH products raise GH without raising KH, so KH needs a separate buffer if you want it. Baking soda (sodium bicarbonate) is a common KH source; chemistry gives roughly 0.03 g per litre for each 1 dKH, but it adds sodium and can push pH up, so go slowly.

Good Practice

  • Mix and dose the new water in a bucket, not in the tank, and check GH and KH with a test kit before adding it.
  • Do not add minerals when topping off evaporated water. Minerals do not evaporate; top off with plain RO/DI.
  • Change hardness gradually. Large GH or KH swings can stress fish and shrimp.
  • Match the target to your species rather than a generic number.
  • Drop test kits have limited precision, so treat results as estimates and adjust after testing.

Units

1 dGH = 17.85 ppm (mg/L as CaCO3). 1 meq/L is about 2.8 dGH (many labels round this to 3 dH). KH works the same way: 1 dKH = 17.85 ppm.

Calculator References

    • Note:States 16 g (1 tablespoon) per 80 L (20 US gallons) raises GH by about 1 meq/L (3 dGH), based on DI or RO water.
    • Note:Minerals do not evaporate, so Equilibrium should not be used when replacing evaporated water.
    • Publisher:Seachem Laboratories, Inc.
    • Accessed:2026-10-26

Ways to Prepare Water for a Target GH

โ† Scroll horizontally to inspect full matrix โ†’
MethodBest forStrengthsWatch out for
Use tap water as isTanks whose species suit your tap hardnessSimple and cheapCannot change hardness
Blend tap with RO/DIHard tap water and soft-water speciesCheaper than full remineralizing, lowers GH and KH togetherOnly lowers hardness; needs tap GH above the target
Remineralize pure RO/DIShrimp, planted tanks and very soft or very hard targetsFull control over GH, optional KHNeeds a scale, label constants and test kits

Always test the prepared water before adding it to the tank. Product constants vary, so use the figures on the pack you actually bought.

Companion Ecosystem

Related Aquarium Calculators

3 Companion Tools

Frequently Asked Questions

How do I calculate GH after a water change?

Multiply the volume of water left in the tank by the tank GH, add the volume of new water multiplied by its GH, then divide by the total volume. A 64 L tank at GH 10 with a 10% change using GH 3 water ends at about 9.3 dGH.

How much RO water do I mix with tap water to reach a target GH?

Use tap fraction = (target GH - RO GH) / (tap GH - RO GH). With tap GH 14, RO GH 0 and a target of 6, you need about 43% tap and 57% RO.

Can I use this when my target is higher than my tap GH?

Blending only lowers hardness. If the target is above your tap GH, you need to add minerals, so use the remineralizing mode instead.

How much Seachem Equilibrium do I add to RO water?

The label says 16 g (about 1 tablespoon) per 80 L (20 US gallons) raises GH by about 3 dGH, which is 0.2 g per litre per 3 dGH. Check the current pack label, and test the water before adding it to the tank.

Does Equilibrium raise KH?

No. It raises GH using calcium, magnesium and potassium salts and does not raise KH. If you want KH, add a separate buffer.

How much baking soda raises KH by 1 dKH?

Chemistry gives about 30 mg per litre, roughly 3 g per 100 L. It adds sodium and can raise pH, so add it gradually and test after mixing.

Should I add minerals when topping off evaporated water?

No. Minerals stay behind when water evaporates, so top off with plain RO/DI water. Remineralize only the water you use for changes.

What is the difference between dGH and ppm?

1 dGH equals about 17.85 ppm expressed as CaCO3. Many test kits and labels switch between the two, so check the unit before entering values.

Why is my measured GH different from the calculated value?

Test kits have limited precision, the label constants are approximate, and substrate or rock can add or absorb minerals. Treat the result as an estimate and adjust after testing.

Where should I mix the water?

Mix and test in a separate bucket or barrel, then add it to the tank. Dosing minerals directly into the tank is harder to control and can cause local spikes.

Can I change hardness quickly?

Avoid large, sudden changes. Move GH and KH in small steps over several water changes, especially with shrimp and sensitive fish.

Does this work for saltwater?

No. This tool is for freshwater GH and KH. Marine salinity and alkalinity use different chemistry and products.